Model: MVWB765FW3 Location: Fort Myers, FL 33967 Repair Summary Checked washer for unbalanced operation. Upon arrival, found the suspension rods were very weak. Replaced the suspension assemblies and adjusted the front leveling feet, as the washer was not properly leveled. Tested with a load of towels using Drain and Spin and verified the washer is now spinning and draining properly with no unbalanced condition or other issues at this time.

Model: RF28R7201SR/AA Location: Lehigh Acres, FL 33936 Repair Summary Checked refrigerator for no ice production and a broken French door mullion assembly. Connected diagnostics and found an active 49 error code indicating an auger fan failure. Also confirmed a 39 ice maker error, which requires replacement of the ice maker and main control board. Inspected the ice system and also found the ice bucket cracked. The refrigerator will require a new auger assembly, ice bucket, ice maker, main control board, and French door mullion assembly. Due to the extent of the required repairs, the cost is beginning to exceed the value of the refrigerator. Customer will contact Samsung to see if any assistance is available.

Model: DW80CG4021SRAA Location: Lehigh Acres, FL 33971 Repair Summary Checked dishwasher for not starting. Upon arrival at the newly constructed home, found the water supply to the dishwasher was turned off under the sink. Turned the water supply back on and tested operation. Verified the dishwasher is now starting and operating properly. Unit checks normal at this time.

Model: RF28R7201SR/AA Location: Estero, FL 33928 Repair Summary Checked refrigerator for a shelf stuck in place. Upon arrival, found a spill had caused the shelf to stick. Removed the clips securing the glass and found one of the clips used to remove the complete shelf assembly was broken, preventing the entire shelf from being removed. Removed the glass portion instead and showed the customer how to properly remove and reinstall the glass for cleaning. Checked the refrigerator for error codes and found an ice maker error. Replaced the ice maker and tested operation. All checks passed at this time. Also noted water pressure was slightly low and found the water filter had been installed since October. Advised the customer to replace the water filter to help improve water flow and ice production.

Model: WRF555SDFZ16 Location: Cape Coral, FL 33993 Repair Summary Checked refrigerator for intermittent ice dispensing. Customer stated the ice maker is producing ice, but the dispenser intermittently will not dispense it. Upon inspection, found the ice maker leaking slightly during the fill cycle. Also found the retaining clip where the ice bin locks into position is broken (see pictures). When the auger motor activates, the broken clip allows the ice bin to push outward instead of remaining securely engaged, preventing proper ice dispensing. Because the bin is being pushed out of position, water dripping from the ice maker is falling between the ice bin and auger assembly rather than directly into the bin. The damaged retaining clip is incorporated into the refrigerator cabinet liner and is not a replaceable component. Due to the location of the damage, this condition is not repairable.

Model: RF28R7201SR/AA Location: Cape Coral, FL 33904 Repair Summary Checked refrigerator for no ice production. Upon arrival, found a large piece of ice jammed along the side of the ice maker, blocking the sensor. Connected HASS and ran a service diagnostic report, which showed several stored ice maker and sensor error codes. Found the IR sensor on the auger motor assembly was not illuminated. Removed the ice maker and auger motor assembly and cleared all ice buildup. Also found one Y-clip missing. Replaced the auger motor assembly, ice maker, and Y-clips. Forced the ice maker to cycle and verified it completed the cycle and called for water properly with no leaks. Checked water pressure and verified good flow. Customer is using a genuine water filter. Cleared the stored error codes and verified none returned. Advised the customer to allow approximately 24 hours for normal ice production. Unit checks normal at this time.

Model: RS27T5200SR/AA Location: North Fort Myers, FL 33917 Repair Summary Checked refrigerator for an intermittent ice maker noise. Customer stated the ice maker would randomly produce ice, but after a period of time it would cycle repeatedly and make a loud noise. Ran HASS diagnostics and found a C26 ice maker error. Initially forced the newer ice maker to cycle and it operated normally; however, after several cycles, the ice maker became stuck during the harvest cycle and produced a loud hammering noise (see video). When this occurred, the ice maker would not call for water. After three additional cycles, it completed the harvest and filled properly. Contacted Samsung and completed Visual Support. The failure was successfully reproduced during the call so Samsung could observe the ice maker malfunctioning. Samsung recommended replacing the refrigerator door along with the ice maker. Also had a main control board available as a precaution due to a previous HASS Overall Check causing the refrigerator to stop operating. Replaced the door and ice maker and tested operation. Verified the ice maker cycled and filled properly with no abnormal noise (see video). Ran the HASS Overall Check and submitted a passing report to Samsung. Advised the customer to allow approximately 24 hours for normal ice production.

Model: WRFC9636RZ00 Location: Saint James City, FL 33956 Repair Summary Checked refrigerator for intermittent power loss. Customer stated the display would go completely blank, followed by a power failure error and audible beeping. Upon arrival, the refrigerator was operating normally and had been for the previous few days. Entered service mode and found no stored error codes or failed components. Verified a stable 120V supply at the outlet and traced power to the main control board with no voltage loss. Inspected the electronics and found no visible shorts or burned components. Replaced the main control board; however, after the compressor started, the display began flashing and the unit intermittently lost power again. Compressor windings tested evenly, and the compressor was not suspected as the cause. Suspected an intermittent short within the low-voltage DC circuit involving the inverter, evaporator fan, or display electronics. Returned and isolated the low-voltage components, activating each fan individually without duplicating the voltage drop. During further testing, the UI/display panel shorted when touched, and while disconnecting it, the connector and solder connection broke away from the panel. This may have been the source of the intermittent short. Replaced the UI/display panel and tested operation. Refrigerator is currently running normally with no flashing display, beeping, or power loss. Advised the customer to monitor the unit for any recurrence.

Model: MRF29D9BST Location: Fort Myers, FL 33919 Repair Summary Checked refrigerator for no cooling. Upon inspection, found the compressor was not running while the remainder of the refrigerator was powered and operating. Tested the compressor windings and measured approximately 16.5 ohms across all three terminals. Ordered the main control board and inverter, with the possibility of compressor replacement if the issue remained. Returned and found the incorrect inverter had been supplied. Replaced the main control board, but the compressor still would not start. Returned with the correct inverter and installed it; however, the compressor still failed to start. Contacted tech support and confirmed the compressor was not starting after replacement of both the main control board and inverter. The unit was submitted for further review, and customer service will contact the customer with the next steps.

Model: RF28R7201SR/AA Location: North Fort Myers, FL 33917 Repair Summary Checked refrigerator for the upper ice maker freezing over. Customer stated we previously serviced the refrigerator for the same issue before they were aware they had an extended warranty. Upon inspection, found the ice room frozen over, which is a known recurring issue with this model (see pictures). Thawed and cleared the ice room and replaced the ice maker and auger assembly. Also found the ice bin cracked and requiring replacement. Customer approved having the replacement ice bin ordered and shipped directly to their home. Cycled the new ice maker and verified proper operation. Advised the customer to allow approximately 24 hours for normal ice production. Explained that although the ice room was thawed and the affected components were replaced, the underlying ice room freezing condition is not permanently repairable and is expected to return.